ModelRailroadForums.com is a free Model Railroad Discussion Forum and photo gallery. We cover all scales and sizes of model railroads. Online since 2002, it's one of the oldest and largest model railroad forums on the web. Whether you're a master model railroader or just getting started, you'll find something of interest here.
Affiliate Disclosure: We may receive a commision from some of the links and ads shown on this website (Learn More Here)
-
-
Dub replied to the thread What tubular track turnouts/switches can accommodate Marx locomotives with fat wheels?.What I did was throw up an elevated loop. Run anything up there unimpeded. If you visit Myflyertrains.net check out page 35 of the 1938... -
Dub replied to the thread What tubular track turnouts/switches can accommodate Marx locomotives with fat wheels?.Prewar AF switches are easy to find. Just look for any three rail AF switches. 027 is a Lionel thing and not made by AF. The switches...
-
Dub replied to the thread What tubular track turnouts/switches can accommodate Marx locomotives with fat wheels?.I am not that familiar with the problem. Marx switches will work and if you are not happy with any postwar switches, how about looking...
-
Dub replied to the thread Can you convert Kusan 2-rail O gauge models to 3-rail operation?.Another idea is to use a Lionel alco motor and frame. If it fits? Then just add Lionel trucks to the other cars. Doing it this way you...
-
I had joined the forum a long time ago, but forgot about it until now. So, I'm Jacob, I'm 32, I run 3-rail O Gauge model trains...
-
Dub replied to the thread Marx steam locomotive questions.Do the best you can. Take your time removing the rods. If it works your done. If not look for another wheel. It should work if the pin...
-
Dub replied to the thread Marx steam locomotive questions.I just keep them on. Taking them off may become a permanent situation. Unless you get into a tap or rivet. For me anyways, removing the...
-
Dub replied to the thread Pre-Wired 3mm LEDs.Thank you for the correction, I would hate to confuse anybody. If I do an Ohm's Law calculation I use .02A, the max value. What do you...
-
If you can solder small stuff - roll your own. @Kusojiji ifn I remember uses SMT resistors and he does his own. As to the 1/4 or 1/2...
-
Dub replied to the thread Pre-Wired 3mm LEDs.Look at voltage amperage and resistance. If the resistance is the same for both voltages the amperage will be lower at higher voltages...
-
Dub reacted to Blk6999's post in the thread Lionel 224 steam engine, questions on motor and tender with
Like.
Had sometime today to revisit my motor. When I bypassed the Eunit it worked. Could see one broken finger on the (2) finger connector... -
Dub reacted to Bruette's post in the thread 23-year-old enthusiast of old-school 3-rail O gauge models with Like.
"23-year-old enthusiast of old-school 3-rail O gauge models" This thread made my day, thank you and welcome aboard!
-
Dub replied to the thread 23-year-old enthusiast of old-school 3-rail O gauge models.If you try again, the manual will reference the 2333 ( pg 173) not the 2343. The only difference that I know of is the 2343 has a newer...
-
Dub replied to the thread 23-year-old enthusiast of old-school 3-rail O gauge models.Welcome to the Forum! Servicing your engines is a good place to start. Your grandfather obviously took care of those trains. They look...
-
Dub replied to the thread Sawdust? What can I use for HO sawdust?.A belt sander with a collection bag will work.
-
-
Loading…
-
Loading…
-
Loading…
Affiliate Disclosure: We may receive a commision from some of the links and ads shown on this website (Learn More Here)